Find Reviews and Compare Prices for:
 
 
 
 
User rating
 
4.5 (1)
 Add a review

GuitarPCB.com Stage 3 Booster V3 PCB

 
This is the new V3 board which is designed with an on board trimmer to give you some extra tweak-ability. You can just use your ear to find the sweet spot. - - This is originally based off of the Fetzer and with some modifications is now a super clean tone booster for either Standard 6 String or Bass Guitar! - - An amazing Tone Boost that will bring life back to your Guitar and Amp combo! - - Amazing for Bass too it is just a simple Cap change via an on board switch. - - Try this instead of a ZVEX ® - Super Hard On™ and get a cleaner more overall tone boost and skip the crackle!


Price: $0 to $0 at 0 stores
Searched GuitarPCB.com Stage 3 Booster V3 PCB in Reviews
 

 

Great beginners pedal build, and awesome tone featured

Ease Of Use The Stage 3 PCB is tiny, like postage stamp tiny. If you are clever enough with your builds you can fit it in a very tiny enclosure. The Stage 3 PCB is very high quality, and easy to solder on.

GuitarPCB.com provide excellent, easy to read and understand guides for building their pedal projects, and the Stage 3 is no exception. The PDF has excellent diagrams showing where to install all components, and wire up the pedal.

I personally had a little difficulty neatly soldering all components and wires to the PCB, but it all still works nicely as it should. I narrowed this down to recently replacing my cheap soldering iron with a better quality Weller soldering iron. It has a far faster heat up time, and better heat transfer than my old one, and I dare say my difficulties were as a result of holding the iron on the board longer than was actually necessary. Now that I'm getting used to my new iron I'm sure my builds will become a bit more tidy again.

I wired the PCB up to the necessary switches, jacks, and potentiometer, and installed it into an enclosure. The Stage 3 needs a steady 9 volt power supply to run, so no batteries here. The JFET used needs to be biased correctly to 4.5V, and fluctuations in voltage from batteries will mean that the pedal will not work correctly.

Once the pedal is built it is extremely easy to use too. One knob for the boost, goes from 0 volume to big boost.


Sound I plugged the Stage 3 into my Blackstar HT-5, putting it in the last place before my amp's input. It is said that the Stage 3 works at it's best last in line, and I saw no reason to not follow that advice.

On the clean channel the stage 3 provided a healthy volume boost, and added a little top end sparkle to my tone. Crank the boost, and it started to provide a little clean crunch.

Switching over to the dirty channel, where I spend most of my time playing, I was amazed by the transformation of my tone. My tone was still the same for the most part, no colouring whatsoever, but it seemed so much more three dimensional, with a new level of clarity and sparkle. I hesitate to use the term, but it really was like lifting a blanket up off my amplifier. Push the boost and the Stage 3 pushed my amp harder, piling on more and more tight, usable distortion.

The beautiful thing with the Stage 3 Boost is that it makes your dirt pedals sound better as well. Everything sounds more full of life and three-dimensional.

Higher levels of boost did introduce a bit of noise to my signal, but that is expected of any pedal that distorts or overdrives your signal. Nothing major though, and I could control it to some extent with my MXR Noise Clamp.

Overall the GuitarPCB.com Stage 3 Booster V3 PCB is not only a great beginners effects pedal build, but also a very useful pedal that will really make your rig sound like a million bucks. It's a nice easy pedal to build


Reliability The PCB itself is very well made, so as long as your build is good, the pedal will most definitely last.


Customer Support The GuitarPCB.com forums give you access to a wealth of experienced, helpful builders who can guide you through the build if you are having difficulties. Barry, the owner of GuitarPCB.com is an awesome person to deal with as well. Always quick to respond to queries, and more than happy to as well.


Liked about it Nice simple build for beginners.
* Awesome tonal upgrade, like lifting a blanket off of a speaker.
* Small PCB, so can fit in a nice small enclosure if you are clever enough with your build.


Didn't like Not that it's really an issue personally, but pedal wont operate on batteries.
* *Does introduce a little noise at higher settings.


Overall satisfaction:
 
4.5

By LonePhantom
Sep 28, 2011
 
Was this review helpful to you?
Yes No

Report this review
 
Price: $0 to $0
Compare Prices
at 0 stores
 
 
























Something wrong in this page? Let us know!
internal use: spec795 spec796