Jemsite - Reply to Topic
All Other Guitars (including Prestige) Discussion about other Ibanez Guitars not covered in the above topics. Includes J-Custom, USA-Custom, Prestige subforum.

Thread: Need help with pocket shim/bridge adjustment Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Jemsite forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address

IMPORTANT: You will be required to activate your account so please ensure that your email address is correct.

If you do not receive your activation check your spam folder before using the CONTACT US form (at the bottom right of each page).



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-04-2015 03:05 PM
Bluestreak
Re: Need help with pocket shim/bridge adjustment

Quote:
Originally Posted by nickf View Post
buzz is everywhere, more so on the E,A,D strings
Sounds like the neck is too flat.

Quote:
Originally Posted by nickf View Post
relief is good, the low E has a tiny bit of room on the 8th/9th fret
What's "a tiny bit"? Measure. Should be in the .3-.5 mm area. I'm willing to bet yours will be lower than 0.3 if you measure it. If it is, you're pushing the boundaries of a "low" setup.

Quote:
Originally Posted by nickf View Post
I did go up and down the fret board with a fret rocker and there are some high frets but nothing too crazy.
Again, measure. An unusually tall fret further up the board on a neck set up to be flatter could easily cause a lot of fret buzz every time you fret and pick a note below that point. It will take patience and some investigation, but if you check the notes where you hear it most commonly then find there's little to no clearance under the string with your feeler gauge, you can narrow down the offending fret position.

Quote:
Originally Posted by nickf View Post
All I want to do is lower the action to something in the ballpark of 1.5mm on the Low E.
That's exceptionally low action for a guitar of this type. Remember, you're not working with Ibanez's highest craftsmanship. It can make a difference. Trying to eek out the lowest setup possible on a guitar of this kind might be asking a bit much. That's why I'm suggesting you break out feeler gauges and measure, adjust, and scientifically chip-away at the problems. I just don't know that 1.5-mm action is going to be achievable with a perfectly clear tone here.

It's also damn hard to give advice on this sort of thing without putting my hands on the thing. There's more you can check I haven't even mentioned yet, typing it's the hard part.
03-04-2015 02:29 PM
nickf
Re: Need help with pocket shim/bridge adjustment

buzz is everywhere, more so on the E,A,D strings, relief is good, the low E has a tiny bit of room on the 8th/9th fret, I did go up and down the fret board with a fret rocker and there are some high frets but nothing too crazy.

Right now my action is like 2.5mm on the low E and maybe 2.0mm on the high e, and most of the saddles are maxed out all the way up. If I lower the saddles any the buzz just get worse.

All I want to do is lower the action to something in the ballpark of 1.5mm on the Low E.

I already had the neck off to see what was in there and to adjust the neck for side to side centering (the low E was really close to the edge of the fretboard in the upper frets) there was no extra paint, or shims in there.

Nick F
03-04-2015 09:49 AM
Bluestreak
Re: Need help with pocket shim/bridge adjustment

You could toss a shim in there and see if it solves the problem, but I think more investigation is necessary. Where's the fret buzz? Low frets? High? All of them? Have you checked the truss rod adjustment? Have you put a straight-edge to the frets, using feeler gauges to check clearances along the neck? When hardware has to be adjusted to an extreme as you describe in your guitar's setup... I don't think a simple shim will compensate that much.
03-03-2015 11:51 PM
RGTFanatic
Re: Need help with pocket shim/bridge adjustment

Quote:
Originally Posted by nickf View Post
So I have and older RG321MOL with the WII neck, really solid guitar, But ever since I got it I have this issue with it. So due to the indo craftmanship i get there will be some fret buzz, but this is a little different.

So everything is stock on the guitar, and the bridge saddles have to be adjusted ALL the way up almost to the point where the screws are coming out of the saddles just so there minimal fret buzz.

So Im thinking that I should put a shim in the neck pocket. All the info I can find on shimming the neck pocket is the opposite condition that I have where the saddles are all the way down and they shim the back (bridge side) of the pocket. Im thinking that I should shim the front (headstock) of the pocket.

Nick F
Hi Nick,
Yes, a headstock side shim will probably solve your problem, but you should pull the neck off first to make sure that there isn't anything in there already that's causing the neck angle you have now.
03-03-2015 04:41 PM
nickf
Need help with pocket shim/bridge adjustment

So I have and older RG321MOL with the WII neck, really solid guitar, But ever since I got it I have this issue with it. So due to the indo craftmanship i get there will be some fret buzz, but this is a little different.

So everything is stock on the guitar, and the bridge saddles have to be adjusted ALL the way up almost to the point where the screws are coming out of the saddles just so there minimal fret buzz.

So Im thinking that I should put a shim in the neck pocket. All the info I can find on shimming the neck pocket is the opposite condition that I have where the saddles are all the way down and they shim the back (bridge side) of the pocket. Im thinking that I should shim the front (headstock) of the pocket.

Nick F

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome