Jemsite - Reply to Topic
All Other Guitars (including Prestige) Discussion about other Ibanez Guitars not covered in the above topics. Includes J-Custom, USA-Custom, Prestige subforum.

Thread: Some question regarding neck. Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Jemsite forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address

IMPORTANT: You will be required to activate your account so please ensure that your email address is correct.

If you do not receive your activation check your spam folder before using the CONTACT US form (at the bottom right of each page).



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
01-12-2006 04:25 AM
ibanez.shredder
Re: Some question regarding neck.

I doubt the manufacturing tolerances are anywhrere near that wide. because the nut is metal and would be the exact (or very close to) width of 43mm for wizard, super wizard and wizard II. therefore the neck has to be very accurate too as the nut wont fit properly, and it would look awful if the nut was wider or narrower than the neck. also the heel width would have to be pretty accurate as well to fit in the neck joint. also dont forget the bodys and neck are cut by an CNC machine which cuts to exact (probably down to microns thick) measurements. Ibanez necks are very consistiant in width and any differnce between one orignal wiazird and another would be minimal and unnoticible
01-12-2006 12:04 AM
Jing
Re: Some question regarding neck.

Maybe* manufacturing tolerances might link to a even greater difference. Lets say wizard neck with the max width in factory will be 42 strictly, and anithing lower can be tolerate and anything higher will not be. So that will be a 40 - 41mm, where as wizard II neck have a min width of 43 and anithing higher than that can be tolerate and anything lower will not be, and that will be a 44-45mm. The differences can be around 5mm.

Don't take it seriously i'm just guessing
01-11-2006 05:01 PM
JESTER700
Re: Some question regarding neck.

Quote:
Originally Posted by markg5150
Is the difference between 42mm and 43mm really noticeable? I'd be surprised if it is, When you take into account manufacturing tolerances surely they'd be the same.
Unless the 42mm erred small & the 43mm erred big. It's about the difference between 1 5/8" and 1 11/16". I feel a little cramped on the typical 1 5/8" neck, and prefer 1 11/16", but since I don't have 2 necks that are the same except for that dimension, it's hard to say.
01-11-2006 02:40 PM
markg5150
Re: Some question regarding neck.

Is the difference between 42mm and 43mm really noticeable? I'd be surprised if it is, When you take into account manufacturing tolerances surely they'd be the same.
01-11-2006 02:02 PM
Jing
Re: Some question regarding neck.

i dont know but i rem hearing it somewhere that they said "shreding" necks are meant to be wide and flat. You guys dont feel it wide? Maybe my fingers are short, normally i measure the neck width by trying to fret 12-15th on low e string. On les paul and wizard II neck, i need to stress a little on my pinky, where one my warmoth i barely need to stress anyone of them maybe i should get a warmoth one again, but 1.5k i dont think its enough although
01-11-2006 06:46 AM
ibanez.shredder
Re: Some question regarding neck.

yup. super wizard, original wizard and wizard 2 all have the same width of 43 mm. you find it too wide? haha fair enough i suppose it is pretty wide. you'd hate my Wizard-7 then!
01-11-2006 04:20 AM
Jing
Re: Some question regarding neck.

actually i dun mind having a thicker or thinner neck. But i really find wizard II neck dam wide, its even wider than my les paul 0.0 so does super wizard and wizard II have the same wideness?
01-10-2006 10:54 PM
JESTER700
Re: Some question regarding neck.

The JS neck is narrower, at 42mm (vs. 43mm on the wizard variants). But there are other differences, too - rounder radius, smaller frets, etc. It's a fine neck, but make sure it feels good in your hand.

You might want to look for a used "ultra" neck - bigger frets, thicker than a wizard (but not much), and 42mm wide at nut. Be sure it's an AANJ (assuming your 470 is) - most ultras weren't...
01-10-2006 06:55 PM
nightfiend14
Re: Some question regarding neck.

well if u decide to get rid of your s470 pm me with a price.
01-10-2006 02:31 PM
chris101
Re: Some question regarding neck.

yes good idea, I ditched my crappy s470dx Qm and bought a jS1200, amazing upgrade!
01-10-2006 10:27 AM
Jing
Some question regarding neck.

I have a s470dx which i rather find the neck too wide compare to my warmoth neck (wide not thickness). Is all wizard, super wizard, wizard 2 that wide? Im thinking of getting a new better axe, but i could't try it out as im ordering online. How about js1200? Im thinking of that

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome