Ibanez JEM Forum banner
jack
1-12 of 12 Results
  1. All Other Guitars (including Prestige)
    I have a Starfield Altair SJ Custom that I bought back in 1992. The jack is missing. it has a hole that is 1.7cm in diameter where the jack is meant to go. I ordered a generic jack plate and jack online, but its too big to fit. Can someone help point me to the jack I should buy?
  2. Pickups & wiring
    Recently I have been finally getting to wiring up a few of my guitars I've had sitting on the backburner. In doing this I've come across several bad input jacks that I've ordered off of ebay. I pretty much always use switchcraft jacks so when I got them I made sure the listing said...
  3. Tech: Setup, Repairs and Mods
    Guys, need your advise : Is this switchcraft female jack could be a direct replacement to any MIJ Ibanez input jack ? No modification needed?
  4. Pickups & wiring
    What's the ultimate quality barrel jack socket? They don't seem to last on my old rg550.
  5. Pickups & wiring
    Hey, It is a common issue for the Output jack nut to come loose often, and I am having this problem with all of my guitars... First is my Ibanez RG350dx, the washer is loose, keep having to unscrew the plate and pinch the back and tighten the front, the screw holes are beggining to get chewed...
  6. All Other Guitars (including Prestige)
    Where in the UK can I buy just the back plate for the jack socket for an old Japanese RG550? I've picked up an old RG /JEM bitsa and I need a back plate as it is missing. Its the one with the three holes and not the modern two holed version. Have scoured Ebay and a few other JEM / RG sites and...
  7. Gear, Equipment, Recording & Off Topic
    Hi everyone, I was wondering if it was possible to move the jack sockets on my Bad Horsie so they're coming out the top of the pedal and not the sides. I know the jack sockets are soldered to the PCB, but can I fit an additional set and then run wires to the corresponding places on the PCB...
  8. Tech: Setup, Repairs and Mods
    I've got an Ibanez RGT42DXFM that I've been upgrading and I'm on the final stages. This is everything so far: Supermassive HSP-90 neck. Bareknuckle nailbomb bridge. Edge pro trem. FU big block. Noisless springs. Brass spring claw. RP tremolo stabiliser. Three way selector switch. Push/pull...
  9. Gear, Equipment, Recording & Off Topic
    Well, i've heard a rumour that touching your jack ends on your guitar cables is bad, as you get crap and grime interfering with the connection when when you plug them in. So i've been told that you should avoid touching the ends and occasionally clean them with contact cleaner to make them the...
  10. Tech: Setup, Repairs and Mods
    Hi all My RG2027 has loose input jacks (ie the lead keeps popping back out). I first saw these: BARREL JACK output socket for Ibanez guitar, bass etc on eBay (end time 05-Jan-11 11:57:54 GMT) and then saw Maplin doing them for £2.15 with free delivery: 6.35mm Stereo Long Reach Chassis Socket...
  11. Pickups & wiring
    Hi dudes, I'm a long time lurker, first time poster here. Thanks for having me 8) Anyway, I'm trying to install an EMG 81/85 into my Ibanez 2550z. The EMG output jack won't fit in the slot, but the Ibanez jack appears to be stereo and I read that it should work. It's one of the barrel type...
  12. Tech: Setup, Repairs and Mods
    Hey guys, just one quick question that needs an answer and I will be on my way. I seem to have lost the nut that holds the input jack on my acoustic guitar (must have gotten loose and fell off). I don't know what size it is (i know the actual jack is a 1/4", right?). So would that mean the...
1-12 of 12 Results
Top