Ibanez JEM Forum banner
killswitch
1-11 of 11 Results
  1. Tech: Setup, Repairs and Mods
    Hey everyone! I recently modded my Jem with a killswitch and thought I'd share the story since it turned out so well. Most killswitches I have tried are these really small buttons that don't perform all that well. The one that always grabbed my attention was the large one on the buckethead...
  2. Classified Ads: Guitars and Gear
    So up for sale is my trusty Jackson DKMGT. Amazing build quality being a MIJ and is a lot of guitar for the money! It's got a Seymour Duncan Custom in the bridge and an Iron gear Rolling Mill in the neck. A custom killswitch has been fitted, and the tone knob is a coil split so there's a...
  3. Pickups & wiring
    Evening all, Can someone that has some knowledge of schematics confirm what I have attached here will work? I copied the wiring from a Dimarzio scheme for the pickups so I'm not too worried there. My main concern is if the kill switch is ok or if I should still have a wire from the mid volume...
  4. Tech: Setup, Repairs and Mods
    hey guys over christmas, i plan to install a killswitch in my guitar, which is an ibanez rg370 dxz. you guys dont appear to like "regular", non prestige/90s RGs, but this is my guitar, and its awesome. Live with it. :P anyway, ive read tons of guides on how to do it but each one tells you to...
  5. Pickups & wiring
    I'm wiring a new set of PUPs into a late 90s RG470. I have a Tone Zone Bridge, Area 67 Middle, and Air Norton Neck. I just want to confirm that I have my wiring correct before I start soldering. Thanks.
  6. Pickups & wiring
    Hey, hope someone can help me. I'm replacing my vol pot on my Washburn N4 with a push/pull and want to wire it up so that 'pot up' kills the neck pickup (to use 3 way toggle as killswitch) and 'pot down' returns it to normal. I have NO CLUE how to do this but I'm very keen to do it myself, I...
  7. Pickups & wiring
    Hey guys, I've recently wired up a killswitch (mini toggle 2 way) to a mates guitar which is 1 pickup 1 volume and a killswitch. I've connected the bare wire to the volume pot ground from the pick up and the white wire to one of the sticking out bits. What do I do with the red wire? Also...
  8. Pickups & wiring
    Well i have been looking around the web for a wiring diagram, but since this isn't a normal RG wiring I want to do I cannot find anything. I was hoping someone here could help. Ibanez V1 Neck p.u. Ibanez S1 Mid. p.u. Ibanez V2 Bridge p.u. 1 vol. pot 5-way p.u. selector DPDT 2-way being used as...
  9. Tech: Setup, Repairs and Mods
    I was wondering if its possible to have a killswitch on a JS1000, and if so are there any wiring schematics out there and 411's on how to get along doing it! P.S I've never done any mods on my guitar ever.
  10. Pickups & wiring
    I created my first external killswitch recently. I liked it so much that I decided I need something more permanent. The guitar I am planning to install it on (a Jackson JSR) however, has only one control - volume. I am reluctant to drill new holes and as a result came with an idea I'd like to...
  11. Pickups & wiring
    Wired a killswitch into my thinline tele in place of neck tone control. Basically, it's a two way switch just before the output jack with position one wired up and two grounded. The only problem is that it hums a bit in the "off" position as though some signal is getting through or it's not...
1-11 of 11 Results
Top